usb_quirk(4freebsd)

NAME

usb_quirk – USB quirks module

SYNOPSIS

To compile this module into the kernel, place the following line in your kernel configuration file:

device usb

Alternatively, to load the module at boot time, place the following line in loader.conf(5):

usb_quirk_load="YES"

DESCRIPTION

The usb_quirk module provides support for dynamically adding and removing quirks for USB devices with usbconfig(8).

General quirks:

UQ_AUDIO_SWAP_LR: swap left and right channels
UQ_AU_INP_ASYNC: input is async despite claim of adaptive
UQ_AU_NO_FRAC: do not adjust for fractional samples
UQ_AU_NO_XU: audio device has broken extension unit
UQ_AU_VENDOR_CLASS: audio device uses vendor class to identify itself
UQ_AU_SET_SPDIF_CM6206: audio device needs special programming to enable S/PDIF audio output
UQ_BAD_ADC: bad audio spec version number
UQ_BAD_AUDIO: device claims audio class, but is not
UQ_BROKEN_BIDIR: printer has broken bidir mode
UQ_BUS_POWERED: device is bus powered, despite claim
UQ_HID_IGNORE: device should be ignored by hid class
UQ_KBD_IGNORE: device should be ignored by kbd class
UQ_KBD_BOOTPROTO: device should set the boot protocol
UQ_UMS_IGNORE: device should be ignored by ums class
UQ_MS_BAD_CLASS: does not identify properly
UQ_MS_LEADING_BYTE: mouse sends an unknown leading byte
UQ_MS_REVZ: mouse has Z-axis reversed
UQ_NO_STRINGS: string descriptors are broken
UQ_POWER_CLAIM: hub lies about power status
UQ_SPUR_BUT_UP: spurious mouse button up events
UQ_SWAP_UNICODE: has some Unicode strings swapped
UQ_CFG_INDEX_1: select configuration index 1 by default
UQ_CFG_INDEX_2: select configuration index 2 by default
UQ_CFG_INDEX_3: select configuration index 3 by default
UQ_CFG_INDEX_4: select configuration index 4 by default
UQ_CFG_INDEX_0: select configuration index 0 by default
UQ_ASSUME_CM_OVER_DATA: assume cm over data feature
UQ_WMT_IGNORE: device should be ignored by wmt driver

USB Mass Storage quirks:

UQ_MSC_NO_TEST_UNIT_READY: send start/stop instead of TUR
UQ_MSC_NO_RS_CLEAR_UA: does not reset Unit Att.
UQ_MSC_NO_START_STOP: does not support start/stop
UQ_MSC_NO_GETMAXLUN: does not support get max LUN
UQ_MSC_NO_INQUIRY: fake generic inq response
UQ_MSC_NO_INQUIRY_EVPD: does not support inq EVPD
UQ_MSC_NO_SYNC_CACHE: does not support sync cache
UQ_MSC_SHUTTLE_INIT: requires Shuttle init sequence
UQ_MSC_ALT_IFACE_1: switch to alternate interface 1
UQ_MSC_FLOPPY_SPEED: does floppy speeds (20kb/s)
UQ_MSC_IGNORE_RESIDUE: gets residue wrong
UQ_MSC_WRONG_CSWSIG: uses wrong CSW signature
UQ_MSC_RBC_PAD_TO_12: pad RBC requests to 12 bytes
UQ_MSC_READ_CAP_OFFBY1: reports sector count, not max sec.
UQ_MSC_FORCE_SHORT_INQ: does not support full inq.
UQ_MSC_FORCE_WIRE_BBB: force BBB wire protocol
UQ_MSC_FORCE_WIRE_CBI: force CBI wire protocol
UQ_MSC_FORCE_WIRE_CBI_I: force CBI with int. wire protocol
UQ_MSC_FORCE_PROTO_SCSI: force SCSI command protocol
UQ_MSC_FORCE_PROTO_ATAPI: force ATAPI command protocol
UQ_MSC_FORCE_PROTO_UFI: force UFI command protocol
UQ_MSC_FORCE_PROTO_RBC: force RBC command protocol

3G Datacard (u3g) quirks:

UQ_MSC_EJECT_HUAWEI: ejects after Huawei USB command
UQ_MSC_EJECT_SIERRA: ejects after Sierra USB command
UQ_MSC_EJECT_SCSIEJECT: ejects after SCSI eject command 0x1b0000000200
UQ_MSC_EJECT_REZERO: ejects after SCSI rezero command 0x010000000000
UQ_MSC_EJECT_ZTESTOR: ejects after ZTE SCSI command 0x850101011801010101010000
UQ_MSC_EJECT_CMOTECH: ejects after C-motech SCSI command 0xff52444556434847
UQ_MSC_EJECT_WAIT: wait for the device to eject
UQ_MSC_EJECT_SAEL_M460: ejects after Sael USB commands
UQ_MSC_EJECT_HUAWEISCSI: ejects after Huawei SCSI command 0x11060000000000000000000000000000
UQ_MSC_EJECT_TCT: ejects after TCT SCSI command 0x06f504025270
UQ_MSC_DYMO_EJECT: ejects after HID command 0x1b5a01

See /sys/dev/usb/quirk/usb_quirk.h or run "usbconfig dump_quirk_names" for the complete list of supported quirks.

LOADER TUNABLE

The following tunable can be set at the loader(8) prompt before booting the kernel, or stored in loader.conf(5).

hw.usb.quirk.%d

The value is a string whose format is:

"VendorId ProductId LowRevision HighRevision UQ_QUIRK,..."

Installs the quirks UQ_QUIRK,... for all USB devices matching VendorId and ProductId which have a hardware revision between and including LowRevision and HighRevision.

VendorId, ProductId, LowRevision and HighRevision are all 16 bits numbers which can be decimal or hexadecimal based.

A maximum of 100 variables hw.usb.quirk.0, .1, ..., .99 can be defined.

If a matching entry is found in the kernel's internal quirks table, it is replaced by the new definition.

Else a new entry is created given that the quirk table is not full.

The kernel iterates over the hw.usb.quirk.N variables starting at N = 0 and stops at N = 99 or the first non-existing one.

EXAMPLES

After attaching a u3g device which appears as a USB device on ugen0.3:

usbconfig -d ugen0.3 add_quirk UQ_MSC_EJECT_WAIT

Enable a Holtec/Keep Out F85 gaming keyboard on ugen1.4:

usbconfig -d ugen1.4 add_quirk UQ_KBD_BOOTPROTO

To install a quirk at boot time, place one or several lines like the following in loader.conf(5):

hw.usb.quirk.0="0x04d9 0xfa50 0 0xffff UQ_KBD_IGNORE"

HISTORY

The usb_quirk module appeared in FreeBSD 8.0, and was written by Hans Petter Selasky ⟨[email protected]⟩. This manual page was written by Nick Hibma ⟨[email protected]⟩.