---
name: "uftdi"
section: "4freebsd"
platform: "linux"
package: "freebsd-manpages"
version: "12.2-2"
release: "Debian 13 (Trixie)"
platforms: ["linux"]
url: "https://new.carta.tech/uftdi/4freebsd"
---

# uftdi(4freebsd)

USB support for serial adapters based on the FTDI family of USB serial adapter chips.

## NAME

**uftdi** – USB support for serial adapters based on the FTDI family of USB serial adapter chips.

## SYNOPSIS

To compile this driver into the kernel, place the following lines in your kernel configuration file:

**device usb** **device ucom** **device uftdi**

Alternatively, to load the driver as a module at boot time, place the following line in [loader.conf(5)](/loader.conf/5.md):

```
uftdi_load="YES"
```

## DESCRIPTION

The **uftdi** driver provides support for various serial adapters based on the following FTDI chips:

- FT8U100AX

- FT8U232AM

- FT8U232BM

- FT232R

- FT2232C

- FT2232D

- FT2232H

- FT4232H

- FT230X

The device is accessed through the [ucom(4)](/ucom/4.md) driver which makes it behave like a [tty(4)](/tty/4.md).

Many of the supported chips provide additional functionality such as bitbang mode and the MPSSE engine for serial bus emulation. The **uftdi** driver provides access to that functionality with the following [ioctl(2)](/ioctl/2.md) calls, defined in ⟨dev/usb/uftdiio.h⟩:

- UFTDIIOC\_RESET\_IO (*int*)

  Reset the channel to its default configuration, flush RX and TX FIFOs.

- UFTDIIOC\_RESET\_RX (*int*)

  Flush the RX FIFO.

- UFTDIIOC\_RESET\_TX (*int*)

  Flush the TX FIFO.

- UFTDIIOC\_SET\_BITMODE (*struct uftdi\_bitmode*)

  Put the channel into the operating mode specified in *mode*, and set the pins indicated by ones in *iomask* to output mode. The *mode* must be one of the *uftdi\_bitmodes* values. Setting *mode* to UFTDI\_BITMODE\_NONE returns the channel to standard UART mode.

  ```
  enum uftdi_bitmodes
  {
  	UFTDI_BITMODE_ASYNC = 0,
  	UFTDI_BITMODE_MPSSE = 1,
  	UFTDI_BITMODE_SYNC = 2,
  	UFTDI_BITMODE_CPU_EMUL = 3,
  	UFTDI_BITMODE_FAST_SERIAL = 4,
  	UFTDI_BITMODE_CBUS = 5,
  	UFTDI_BITMODE_NONE = 0xff,
  };
  struct uftdi_bitmode
  {
  	uint8_t mode;
  	uint8_t iomask;
  };
  ```

  Manuals and application notes published by FTDI describe these modes in detail. To use most of these modes, you first put the channel into the desired mode, then you [read(2)](/read/2.md) and [write(2)](/write/2.md) data which either reflects pin state or is interpreted as MPSSE commands and parameters, depending on the mode.

- UFTDIIOC\_GET\_BITMODE (*struct uftdi\_bitmode*)

  Return the current bitbang mode in the *mode* member, and the state of the DBUS0..DBUS7 pins at the time of the call in the *iomask* member. The pin state can be read while the chip is in any mode, including UFTDI\_BITMODE\_NONE (UART) mode.

- UFTDIIOC\_SET\_ERROR\_CHAR (*int*)

  Set the character which is inserted into the buffer to mark the point of an error such as FIFO overflow.

- UFTDIIOC\_SET\_EVENT\_CHAR (*int*)

  Set the character which causes a partial FIFO full of data to be returned immediately even if the FIFO is not full.

- UFTDIIOC\_SET\_LATENCY (*int*)

  Set the amount of time to wait for a full FIFO, in milliseconds. If more than this much time elapses without receiving a new character, any characters in the FIFO are returned.

- UFTDIIOC\_GET\_LATENCY (*int*)

  Get the current value of the latency timer.

- UFTDIIOC\_GET\_HWREV (*int*)

  Get the hardware revision number. This is the *bcdDevice* value from the *usb\_device\_descriptor*.

- UFTDIIOC\_READ\_EEPROM (*struct uftdi\_eeio*)

  Read one or more words from the configuration eeprom. The FTDI chip performs eeprom I/O in 16-bit words. Set *offset* and *length* to values evenly divisible by two before the call, and the *data* array will contain the requested values from eeprom after the call.

  ```
  struct uftdi_eeio
  {
  	uint16_t offset;
  	uint16_t length;
  	uint16_t data[64];
  };
  ```

  The FT232R chip has an internal eeprom. An external serial eeprom is optional on other FTDI chips. The eeprom may contain 64, 128, or 256 words, depending on the part used. Multiple calls may be needed to read or write the larger parts. When no eeprom is present, all words in the returned data are 0xffff. An erased eeprom also reads as all 0xffff.

- UFTDIIOC\_WRITE\_EEPROM (*struct uftdi\_eeio*)

  Write one or more words to the configuration eeprom. The *uftdi\_eeio* values are as described for UFTDIIOC\_READ\_EEPROM.

  The FTDI chip does a blind write to the eeprom, and it will appear to succeed even when no eeprom is present. To ensure a good write you must read back and verify the data. It is *not* necessary to erase before writing. Any position within the eeprom can be overwritten at any time.

- UFTDIIOC\_ERASE\_EEPROM (*int*)

  Erase the entire eeprom. This is useful primarily for test and debugging, as there is no need to erase before writing. To help prevent accidental erasure caused by calling the wrong ioctl, you must pass the special value UFTDI\_CONFIRM\_ERASE as the argument to this ioctl.

## HARDWARE

The **uftdi** driver supports the following adapters:

- B&B Electronics USB-\>RS422/485 adapter

- Elexol USB MOD1 and USB MOD3

- HP USB-Serial adapter shipped with some HP laptops

- Inland UAS111

- QVS USC-1000

- Buffalo PC-OP-RS / Kurouto-shikou KURO-RS universal remote

- Prologix GPIB-USB Controller

## FILES

- */dev/ttyU\**

  for callin ports

- */dev/ttyU\*.init*

  - */dev/ttyU\*.lock*

  corresponding callin initial-state and lock-state devices

- */dev/cuaU\**

  for callout ports

- */dev/cuaU\*.init*

  - */dev/cuaU\*.lock*

  corresponding callout initial-state and lock-state devices

## SEE ALSO

[tty(4)](/tty/4.md), [ucom(4)](/ucom/4.md), [usb(4)](/usb/4.md)

## HISTORY

The **uftdi** driver appeared in FreeBSD 4.8 from NetBSD 1.5.