--- name: "scbus" section: "4" platform: "freebsd" package: "base" version: "16.0-CURRENT-20261027-61c70dc16a79" release: "FreeBSD 16.0-CURRENT (2026-10-27)" platforms: ["linux", "freebsd"] url: "https://new.carta.tech/SCSI" --- # scbus(4) Common Access Method Storage subsystem Part of [SCSI(4)](/SCSI/4.md). ## NAME **CAM** – Common Access Method Storage subsystem ## SYNOPSIS **device scbus** **device ada** **device cd** **device ch** **device da** **device pass** **device pt** **device sa** **options CAMDEBUG** **options CAM\_DEBUG\_BUS=-1** **options CAM\_DEBUG\_TARGET=-1** **options CAM\_DEBUG\_LUN=-1** **options CAM\_DEBUG\_COMPILE=CAM\_DEBUG\_INFO\|CAM\_DEBUG\_CDB\|CAM\_DEBUG\_PROBE** **options CAM\_DEBUG\_FLAGS=CAM\_DEBUG\_INFO\|CAM\_DEBUG\_CDB** **options CAM\_MAX\_HIGHPOWER=4** **options SCSI\_NO\_SENSE\_STRINGS** **options SCSI\_NO\_OP\_STRINGS** **options SCSI\_DELAY=8000** ## DESCRIPTION The **CAM** subsystem provides a uniform and modular system for the implementation of drivers to control various SCSI, ATA, NVMe, and MMC / SD devices, and to utilize different SCSI, ATA, NVMe, and MMC / SD host adapters through host adapter drivers. When the system probes buses, it attaches any devices it finds to the appropriate drivers. The [pass(4)](/pass/4.md) driver, if it is configured in the kernel, will attach to all devices. ## SYSCTL VARIABLES The following variables are available as both [sysctl(8)](/sysctl/8.md) variables and [loader(8)](/loader/8.md) tunables: - *kern.cam.cam\_srch\_hi* Search above LUN 7 for SCSI3 and greater devices. - *kern.cam.tur\_timeout* Timeout, in ms, for the initial TESTUNITREADY command we send to the devices during their initial probing. Defaults to 1s. FreeBSD 15 and earlier set this to 60s. - *kern.cam.inquiry\_timeout* Timeout, in ms, for the initial INQUIRY command we send to the devices during their initial probing. Defaults to 1s. FreeBSD 15 and earlier set this to 60s. - *kern.cam.reportluns\_timeout* Timeout, in ms, for the initial REPORTLUNS command we send to the devices during their initial probing. Defaults to 50s. - *kern.cam.max\_high\_power* The maximum number high power commands, like START UNIT, to issue at the same time. Defaults to 4. - *kern.cam.modesense\_timeout* Timeout, in ms, for the initial MODESENSE command we send to the devices during their initial probing. Defaults to 1s. FreeBSD 15 and earlier set this to 60s. ## KERNEL CONFIGURATION There are a number of generic kernel configuration options for the **CAM** subsystem: - CAM\_BOOT\_DELAY Additional time to wait after the static parts of the kernel have run to allow for discovery of additional devices which may take time to connect, such as USB attached storage. - CAM\_IOSCHED\_DYNAMIC Enable dynamic decisions in the I/O scheduler based on hints and the current performance of the storage devices. - CAM\_IO\_STATS Enable collection of statistics for periph devices. - CAM\_TEST\_FAILURE Enable ability to simulate I/O failures. - CAMDEBUG This option compiles in all the **CAM** debugging printf code. This will not actually cause any debugging information to be printed out when included by itself. See below for details. - CAM\_MAX\_HIGHPOWER=4 This sets the maximum allowable number of concurrent "high power" commands. A "high power" command is a command that takes more electrical power than most to complete. An example of this is the SCSI START UNIT command. Starting a disk often takes significantly more electrical power than normal operation. This option allows the user to specify how many concurrent high power commands may be outstanding without overloading the power supply on his computer. - SCSI\_NO\_SENSE\_STRINGS This eliminates text descriptions of each SCSI Additional Sense Code and Additional Sense Code Qualifier pair. Since this is a fairly large text database, eliminating it reduces the size of the kernel somewhat. This is primarily necessary for boot floppies and other low disk space or low memory space environments. In most cases, though, this should be enabled, since it speeds the interpretation of SCSI error messages. Do not let the "kernel bloat" zealots get to you -- leave the sense descriptions in your kernel! - SCSI\_NO\_OP\_STRINGS This disables text descriptions of each SCSI opcode. This option, like the sense string option above, is primarily useful for environments like a boot floppy where kernel size is critical. Enabling this option for normal use is not recommended, since it slows debugging of SCSI problems. - SCSI\_DELAY=8000 This is the SCSI "bus settle delay." In **CAM**, it is specified in *milliseconds*, not seconds like the old SCSI layer used to do. When the kernel boots, it sends a bus reset to each SCSI bus to tell each device to reset itself to a default set of transfer negotiations and other settings. Most SCSI devices need some amount of time to recover from a bus reset. Newer disks may need as little as 100ms, while old, slow devices may need much longer. If the SCSI\_DELAY is not specified, it defaults to 2 seconds. The minimum allowable value for SCSI\_DELAY is "100", or 100ms. One special case is that if the SCSI\_DELAY is set to 0, that will be taken to mean the "lowest possible value." In that case, the SCSI\_DELAY will be reset to 100ms. All devices and buses support dynamic allocation so that an upper number of devices and controllers does not need to be configured; **device da** will suffice for any number of disk drivers. The devices are either *wired* so they appear as a particular device unit or *counted* so that they appear as the next available unused unit. Units are wired down by setting kernel environment hints. This is usually done either interactively from the [loader(8)](/loader/8.md), or automatically via the */boot/device.hints* file. The basic syntax is: ``` hint.device.unit.property="value" ``` Individual **CAM** bus numbers can be wired down to specific controllers with a config line similar to the following: ``` hint.scbus.0.at="mpr1" ``` This assigns **CAM** bus number 0 to the *mpr1* driver instance. For controllers supporting more than one bus, a particular bus can be assigned as follows: ``` hint.scbus.0.at="ahci1" hint.scbus.0.bus="1" ``` This assigns **CAM** bus 0 to the bus 1 instance on *ahci1*. Peripheral drivers can be wired to a specific bus, target, and lun as so: ``` hint.da.0.at="scbus0" hint.da.0.target="0" hint.da.0.lun="0" ``` This assigns *da0* to target 0, unit (lun) 0 of scbus 0. Omitting the target or unit hints will instruct **CAM** to treat them as wildcards and use the first respective counted instances. These examples can be combined together to allow a peripheral device to be wired to any particular controller, bus, target, and/or unit instance. This also works with [nvme(4)](/nvme/4.md) drives. ``` hint.nvme.4.at="pci7:0:0" hint.scbus.10.at="nvme4" hint.nda.10.at="scbus10" hint.nda.10.target="1" hint.nda.10.lun="12" hint.nda.11.at="scbus10" hint.nda.11.target="1" hint.nda.11.lun="2" ``` This assigns the NVMe card at PCI bus 7 slot 0 function 1 to scbus 10. The target for [nda(4)](/nda/4.md) devices is always 1. The unit is the namespace identifier from the drive. The namespace id 1 is exported as *nda10* and namespace id 2 is exported as *nda11*. For devices that provide a serial number, units may be wired to that serial number without regard where the drive is attached: ``` hint.nda.3.sn="CY0AN07101120B12P" hint.da.44.sn="143282400011" hint.ada.2.sn="A065D591" ``` wires *nda3*, *da44*, and *ada2* to drives with the specified serial numbers. One need not specify an *at* line when serial numbers are used. ## ADAPTERS The system allows common device drivers to work through many different types of adapters. The adapters take requests from the upper layers and do all IO between the SCSI, ATA, NVMe, or MMC / SD bus and the system. The maximum size of a transfer is governed by the adapter. Most adapters can transfer 1MB in a single operation, however many can transfer larger amounts. ## TARGET MODE Some adapters support *target* *mode* in which the system is capable of operating as a device, responding to operations initiated by another system. Target mode is supported for some adapters, but is not yet complete for this version of the **CAM** SCSI subsystem. ## ARCHITECTURE The **CAM** subsystem glues together the upper layers of the system to the storage devices. PERIPH devices accept storage requests from GEOM and other upper layers of the system and translates them into protocol requests. XPT (transport) dispatches these protocol requests to a SIM driver. A SIM driver takes protocol requests and translates them into hardware commands the host adapter understands to transfer the protocol requests, and data (if any) to the storage device. The CCB transports these requests around as messages. ### CAM The Common Access Method was a standard defined in the 1990s to talk to disk drives. FreeBSD is one of the few operating systems to fully implement this model. The interface between different parts of CAM is the CCB (or CAM Control Block). Each CCB has a standard header, which contains the type of request and dispatch information, and a command specific portion. A CAM Periph generates requests. The XPT layer dispatches these requests to the appropriate SIM. Some CCBs are sent directly to the SIM for immediate processing, while others are queued and complete when the I/O has finished. A SIM takes CCBs and translates them into hardware specific commands to push the SCSI CDB or other protocol control block to the peripheral, along with setting up the DMA for the associated data. ### Periph Devices A periph driver knows how to translate standard requests into protocol messages that a SIM can deliver to hardware. These requests can come from any upper layer source, but primarily come in via GEOM as a bio request. They can also come in directly from character device requests for tapes and pass through commands. Disk devices, or direct access (da) in CAM, are one type of peripheral. These devices present themselves to the kernel a device ending in “da”. Each protocol has a unique device name: - [da(4)](/da/4.md) SCSI or SAS device, or devices that accept SCSI CDBs for I/O. - [ada(4)](/ada/4.md) ATA or SATA device - [nda(4)](/nda/4.md) NVME device - sdda(4) An SD or MMC block storage device. Tape devices are called serial access( [sa(4)](/sa/4.md)) in CAM. They interface to the system via a character device and provide [ioctl(2)](/ioctl/2.md) control for tape drives. The [pass(4)](/pass/4.md) device will pass through CCB requests from userland to the SIM directly. The device is used to send commands other than read, write, trim or flush to a device. The [camcontrol(8)](/camcontrol/8.md) command uses this device. ### XPT drivers The transport driver connects the periph to the SIM. It is not configured separately. It is also responsible for device discovery for those SIM drivers that do not enumerate themselves. ### SIM driver SIM used to stand for SCSI Interface Module. Now it is just SIM because it understands protocols other than SCSI. There are two types of SIM drivers: virtual and physical. Physical SIMs are typically called host bus adapters (HBA), but not universally. Virtual SIM drivers are for communicating with network or virtual machine hosts. ## FILES see other **CAM** device entries. ## DIAGNOSTICS An XPT\_DEBUG CCB can be used to enable various amounts of tracing information on any specific bus/device from the list of options compiled into the kernel. There are currently seven debugging flags that may be compiled in and used: - CAM\_DEBUG\_INFO This flag enables general informational printfs for the device or devices in question. - CAM\_DEBUG\_TRACE This flag enables function-level command flow tracing i.e., kernel printfs will happen at the entrance and exit of various functions. - CAM\_DEBUG\_SUBTRACE This flag enables debugging output internal to various functions. - CAM\_DEBUG\_CDB This flag will cause the kernel to print out all ATA and SCSI commands sent to a particular device or devices. - CAM\_DEBUG\_XPT This flag will enable command scheduler tracing. - CAM\_DEBUG\_PERIPH This flag will enable peripheral drivers messages. - CAM\_DEBUG\_PROBE This flag will enable devices probe process tracing. Some of these flags, most notably CAM\_DEBUG\_TRACE and CAM\_DEBUG\_SUBTRACE, will produce kernel printfs in EXTREME numbers. Users can enable debugging from their kernel config file, by using the following kernel config options: - CAMDEBUG This builds into the kernel all possible **CAM** debugging. - CAM\_DEBUG\_COMPILE This specifies support for which debugging flags described above should be built into the kernel. Flags may be ORed together if the user wishes to see printfs for multiple debugging levels. - CAM\_DEBUG\_FLAGS This sets the various debugging flags from a kernel config file. - CAM\_DEBUG\_BUS Specify a bus to debug. To debug all buses, set this to -1. - CAM\_DEBUG\_TARGET Specify a target to debug. To debug all targets, set this to -1. - CAM\_DEBUG\_LUN Specify a lun to debug. To debug all luns, set this to -1. Users may also enable debugging on the fly by using the [camcontrol(8)](/camcontrol/8.md) utility, if wanted options built into the kernel. See [camcontrol(8)](/camcontrol/8.md) for details. ## SEE ALSO - **Commands:** [camcontrol(8)](/camcontrol/8.md), [camdd(8)](/camdd/8.md) - **Libraries:** [cam(3)](/cam/3.md) - **Periph** **Drivers:** [ada(4)](/ada/4.md), [da(4)](/da/4.md), [nda(4)](/nda/4.md), [pass(4)](/pass/4.md), [sa(4)](/sa/4.md) - **SIM** **Devices:** [aac(4)](/aac/4.md), [aacraid(4)](/aacraid/4.md), [ahc(4)](/ahc/4.md), [ahci(4)](/ahci/4.md), [ata(4)](/ata/4.md), aw\_mmc(4), [ciss(4)](/ciss/4.md), [hv\_storvsc(4)](/hv_storvsc/4.md), [isci(4)](/isci/4.md), [iscsi(4)](/iscsi/4.md), [isp(4)](/isp/4.md), [mpr(4)](/mpr/4.md), [mps(4)](/mps/4.md), [mpt(4)](/mpt/4.md), [mrsas(4)](/mrsas/4.md), [mvs(4)](/mvs/4.md), [nvme(4)](/nvme/4.md), [pms(4)](/pms/4.md), [pvscsi(4)](/pvscsi/4.md), [sdhci(4)](/sdhci/4.md), [smartpqi(4)](/smartpqi/4.md), [sym(4)](/sym/4.md), [tws(4)](/tws/4.md), [umass(4)](/umass/4.md), [virtio\_scsi(4)](/virtio_scsi/4.md) - **Deprecated** **or** **Poorly** **Supported** **SIM** **Devices:** [ahd(4)](/ahd/4.md), [amr(4)](/amr/4.md), [arcmsr(4)](/arcmsr/4.md), [esp(4)](/esp/4.md), [hpt27xx(4)](/hpt27xx/4.md), [hptiop(4)](/hptiop/4.md), [hptmv(4)](/hptmv/4.md), [hptnr(4)](/hptnr/4.md), [iir(4)](/iir/4.md) [mfi(4)](/mfi/4.md), [sbp(4)](/sbp/4.md), [twa(4)](/twa/4.md) - **DTrace** **Providers:** [dtrace\_cam(4)](/dtrace_cam/4.md) ## HISTORY The **CAM** SCSI subsystem first appeared in FreeBSD 3.0. The **CAM** ATA support was added in FreeBSD 8.0. ## AUTHORS The **CAM** SCSI subsystem was written by Justin Gibbs and Kenneth Merry. The **CAM** ATA support was added by Alexander Motin ⟨*mav@FreeBSD.org*⟩. The **CAM** NVMe support was added by Warner Losh ⟨*imp@FreeBSD.org*⟩.