rad.conf(5)

Macros

A macro is defined with a command of the form name=value. The macro name can contain letters, digits, and underscores and cannot be a reserved word (for example, interface). Within unquoted arguments, the string $name is later expanded to value.

Global configuration

The global configuration section sets defaults for router advertisement messages. These can be overwritten in interface blocks.

default router (yes|no)

Act as a default router or not. The default is yes.

dns {option ...}

Add a DNS router advertisement option to communicate network provided nameservers. In a dns block, a search option or at least one nameserver option is required, whereas specifying the lifetime is optional:

lifetime seconds

The number of seconds the dns options are valid after receiving a router advertisement message. The default is 3600 seconds.

nameserver (address|{address ...})

IPv6 address or list of IPv6 addresses of DNS name servers.

search (domain|{domain ...})

Domain or list of domains for the resolv.conf(5) search list.

hop limit hops

Specify the diameter of the internet. The default is 0, meaning unspecified by this router.

managed address configuration (yes|no)

If set to yes, indicate that stateless address configuration prefixes are not available and hosts should consult DHCPv6. The default is no.

mtu bytes

The MTU option is used in Router Advertisement messages to ensure that all nodes on a link use the same MTU value in those cases where the link MTU is not well known. The default is 0, meaning unspecified by this router.

nat64 prefix prefix [{option ...}]

Add a PREF64 router advertisement option to communicate prefixes used for Network Address and Protocol Translation from IPv6 to IPv4 (NAT64). If prefix is specified without a prefix length, its default is 64.

nat64 prefix options are as follows:

lifetime seconds

The number of seconds the nat64 prefix option is valid after receiving a router advertisement message. A value of zero indicates to not use the prefix anymore. The maximum is 65528 seconds. The default is 3600 seconds.

other configuration (yes|no)

If set to yes, hosts should consult DHCPv6 for additional configuration like NTP servers or DNS name servers. The default is no.

router lifetime seconds

The number of seconds this router is a valid default router after receiving a router advertisement message. The default is 3600 seconds.

router preference (high|medium|low)

Indicate whether to prefer this router over other default routers. The default is medium.

reachable time number

The time, in milliseconds, that a node assumes a neighbor is reachable. The default is 0, meaning unspecified by this router. This option is ignored by slaacd(8) and cannot be set on OpenBSD IPv6 hosts.

retrans timer number

The time, in milliseconds, between retransmitted Neighbor Solicitation messages. The default is 0, meaning unspecified by this router. This option is ignored by slaacd(8) and cannot be set on OpenBSD IPv6 hosts.

source link-layer address (yes|no)

Add a source link-layer address option to router advertisement messages, to communicate the link-layer address of the sending interface. The default is yes.

Interfaces

This section contains a list of interfaces or interface groups to send advertisements on. At least one interface is required.

interface name [{prefix ...}]

Options set in the global section can be overwritten inside an interface block. In addition an interface block can contain a list of prefixes:

[no] auto prefix [{option ...}]

prefix prefix [{option ...}]

The default is to discover prefixes to announce by inspecting the IPv6 addresses configured on an interface. This can be disabled with no auto prefix. If prefix is specified without a prefix length, its default is 64.

prefix options are as follows:

autonomous address-configuration (yes|no)

This prefix can be used to generate IPv6 addresses. The default is yes.

on-link (yes|no)

This prefix is considered on-link. The default is yes.

preferred lifetime seconds

The preferred lifetime (pltime) in seconds for addresses generated from this prefix. The default is 2700. This option is ignored if the prefix is discovered from a network interface and it has a lower preferred lifetime.

valid lifetime seconds

The valid lifetime (vltime) in seconds for addresses generated from this prefix. The default is 3600. This option is ignored if the prefix is discovered from a network interface and it has a lower valid lifetime.