---
name: "divaload"
section: "8"
platform: "linux"
package: "isdnactivecards"
version: "1:3.12.2007-11-27-1+b1"
release: "Debian 10 (Buster)"
platforms: ["linux"]
url: "https://new.carta.tech/divaload"
---

# divaload(8)

configure Eicon Diva active ISDN card

## NAME

divaload - configure Eicon Diva active ISDN card

## SYNOPSIS

divaload controller protocol \[options\]

## DESCRIPTION

**divaload** is used to setup the Eicon Diva card for the proper configuration.

## OPTIONS

- **controller**

  selects the controller (card). This can be either:\
   **-c n**\
   where **n** is the controller number, or\
   **-all**\
   to operate on all cards.

- **protocol**

  can be one of the following:

  ```
    -f 1TR6     Germany, old protocol for PABX................ PRI & BRI
    -f ETSI     DSS1, Europe (Germany, ...)................... PRI & BRI
    -f FRANC    VN3, France, old protocol for PABX............ PRI & BRI
    -f BELG     NET3, Belgien, old protocol for PABX.......... PRI & BRI
    -f SWED     DSS1 with CRC4 off, Sweden, Benelux........... PRI
    -f NI       NI1, NI2, North America, National ISDN........ PRI & BRI
    -f 5ESS     5ESS, North America, AT&T..................... PRI & BRI
    -f JAPAN    Japan, INS-NET64.............................. PRI & BRI
    -f ATEL     ATEL, Australia, old TPH1962.................. PRI & BRI
    -f US       North America, Auto Detect....................       BRI
    -f ITALY    DSS1, Italy................................... PRI & BRI
    -f TWAN     DSS1, Taiwan.................................. PRI & BRI
    -f AUSTRAL  Australia, Microlink (TPH1962), On Ramp ETSI.. PRI & BRI
    -f 4ESS_SDN 4ESS Software Defined Network................. PRI
    -f 4ESS_SDS 4ESS Switched Digital Service................. PRI
    -f 4ESS_LDS 4ESS Long Distance Service.................... PRI
    -f 4ESS_MGC 4ESS Megacom.................................. PRI
    -f 4ESS_MGI 4ESS Megacom International.................... PRI
    -f HONGKONG Hongkong...................................... PRI & BRI
    -f RBSCAS   Robbed Bit Signaling, CAS..................... PRI
    -f QSIG     QSIG, Intra PABX link protocol................ PRI & BRI
  ```

The following options may be given to **divaload**.

- **-e \[***1,2,3***\]**

  set Layer 1 framing on PRI Adapter

**1** - doubleframing (NO CRC4)\
 **2** - multiframing (CRC4)\
 **3** - autodetection

- **-x**

  set PRI Adapter in NT mode; default mode is TE

- **-z**

  set PRI Adapter in High Impedance state until first user application does request interface activation

- **-l \[***1...30***\]**

  set starting channel number on PRI Adapter. By default the allocation of channels is made on a high-to-low basis. By specifying -l you select a low-to-high allocation policy (in addition)

- **-q \[***0..3***\]**

  select QSIG options

**0** - CR and CHI 2 Bytes long (default)\
 **1** - CR 1 byte, CHI 2 bytes\
 **2** - CR is 2 bytes, CHI is 1 byte\
 **3** - CR and CHI 1 byte\
 (CR - Call Reference, CHI - B-Channel Ident.)

- **-n \[***0...20***\]**

  select NT2 mode and default length of DIDN (DIDN - Direct Inward Dial Number)

- **-o**

  turn off order checking of information elements

- **-p \[***1,2***\]**

  establish a permanent connection (e.g. leased line configuration)

**1** - TE \<-\> TE mode, structured line\
 **2** - NT \<-\> TE mode, raw line

- **-s \[***0,1,2,3***\]**

  D-Channel Layer 2 activation policy on BRI Adapter

**0** - On demand\
 **1** - Deactivation only by NT side, preferred, default\
 **2** - Always active\
 **3** - Always active, mode 2

- **-t \[***0...63***\]**

  specifies a fixed TEI value (Default is a automatic TEI assignment)

- **-u**

  select point to point mode on BRI Adapter; uses default TEI '0', NT2 mode is on

- **-\[***1...8***\]oad\|osa\|spid**

  BRI Adapter B-Channel options Specify the Originating Address (OAD), Originating Sub-address (OSA) and/or Service Profile Identifier (SPID) for each B-channel (1 or 2 by BRI, 1...8 by 4BRI)\
   Example: -1oad 123456 -1spid 1234560001

- **-d**

  display protocol options summary

- **-w**

  select alternative protocol code directory.\
   default directory: "/usr/share/isdn"

- **-h** *or* **-?**

  help

## AUTHOR

manpage written from -h output by Paul Slootman \<paul@debian.org\>.