--- name: "DS2740" section: "3" platform: "linux" package: "owfs-doc" version: "3.2p4+dfsg1-6" release: "Debian 13 (Trixie)" platforms: ["linux"] url: "https://new.carta.tech/DS2740" --- # DS2740(3) High-Precision Coulomb Counter ## NAME **DS2740** - High-Precision Coulomb Counter ## SYNOPSIS Voltage and Switch **36** \[.\]XXXXXXXXXXXX\[XX\]\[/\[ **memory** \| **PIO** \| **sensed** \| **vis** \| **vis\_B** \| **volthours** \|\ **smod** \|\ **address** \| **crc8** \| **id** \| **locator** \| **r\_address** \| **r\_id** \| **r\_locator** \| **type** \]\] ## FAMILY CODE *36* ## SPECIAL PROPERTIES ### memory *read-write, binary*\ Access to the full 256 byte memory range. Much of this space is reserved or special use. User space is the *page* area.\ See the *DATASHEET* for a full memory map. ### PIO *write-only, yes-no*\ Controls the PIO pin allowing external switching.\ Writing "1" turns the PIO pin on (conducting). Writing "0" makes the pin non-conducting. The logical state of the voltage can be read with the *sensed* property. This will reflect the current voltage at the pin, not the value sent to *PIO*\ Note also that *PIO* will also be altered by the power-status of the *DS2670* See the datasheet for details. ### sensed *read-only, yes-no*\ The logical voltage at the PIO pin. Useful only if the *PIO* property is set to "0" (non-conducting).\ Value will be 0 or 1 depending on the voltage threshold. ### vis *read-only, floating point*\ Current sensor reading (unknown external resistor). Measures the voltage gradient between the Vis pins. Units are in **Volts**\ The *vis* readings are integrated over time to provide the *volthours* property.\ The *current* reading is derived from *vis* assuming the internal 25 mOhm resistor is employed. There is no way to know this through software. ### vis\_B *read-only, floating point*\ Current sensor reading (unknown external resistor). Measures the voltage gradient between the Vis pins. Units are in **Volts**\ The *vis* readings are integrated over time to provide the *volthours* property.\ The *vis\_B* is from a different tuning of the *DS2740 (3)* chip with faster sampling and lower resolution. There is no way to know this through software. ### volthours *read-write, floating point*\ Integral of *vis* over time. Units are in **volthours** ## OBSCURE PROPERTIES ### smod *read-write, yes-no*\ Bit flags corresponding to various battery management functions of the chip. See the *DATASHEET* for details of the identically named entries.\ In general, writing "0" corresponds to a 0 bit value, and non-zero corresponds to a 1 bit value.\ Default power-on state for the corresponding properties. ## STANDARD PROPERTIES ### address ### r\_address *read-only, ascii*\ The entire 64-bit unique ID. Given as upper case hexadecimal digits (0-9A-F).\ *address* starts with the *family* code\ *r address* is the *address* in reverse order, which is often used in other applications and labeling. ### crc8 *read-only, ascii*\ The 8-bit error correction portion. Uses cyclic redundancy check. Computed from the preceding 56 bits of the unique ID number. Given as upper case hexadecimal digits (0-9A-F). ### family *read-only, ascii*\ The 8-bit family code. Unique to each *type* of device. Given as upper case hexadecimal digits (0-9A-F). ### id ### r\_id *read-only, ascii*\ The 48-bit middle portion of the unique ID number. Does not include the family code or CRC. Given as upper case hexadecimal digits (0-9A-F).\ *r id* is the *id* in reverse order, which is often used in other applications and labeling. ### locator ### r\_locator *read-only, ascii*\ Uses an extension of the 1-wire design from iButtonLink company that associated 1-wire physical connections with a unique 1-wire code. If the connection is behind a **Link Locator** the *locator will show a unique 8-byte number (16 character hexadecimal) starting with family code FE.*\ If no **Link Locator** is between the device and the master, the *locator* field will be all FF.\ *r locator* is the *locator* in reverse order. ### present (DEPRECATED) *read-only, yes-no*\ Is the device currently *present* on the 1-wire bus? ### type *read-only, ascii*\ Part name assigned by Dallas Semi. E.g. *DS2401* Alternative packaging (iButton vs chip) will not be distiguished. ## ALARMS None. ## DESCRIPTION ### 1-Wire *1-wire* is a wiring protocol and series of devices designed and manufactured by Dallas Semiconductor, Inc. The bus is a low-power low-speed low-connector scheme where the data line can also provide power. Each device is uniquely and unalterably numbered during manufacture. There are a wide variety of devices, including memory, sensors (humidity, temperature, voltage, contact, current), switches, timers and data loggers. More complex devices (like thermocouple sensors) can be built with these basic devices. There are also 1-wire devices that have encryption included. The 1-wire scheme uses a single *bus master* and multiple *slaves* on the same wire. The bus master initiates all communication. The slaves can be individually discovered and addressed using their unique ID. Bus masters come in a variety of configurations including serial, parallel, i2c, network or USB adapters. ### OWFS design *OWFS* is a suite of programs that designed to make the 1-wire bus and its devices easily accessible. The underlying principle is to create a virtual filesystem, with the unique ID being the directory, and the individual properties of the device are represented as simple files that can be read and written. Details of the individual slave or master design are hidden behind a consistent interface. The goal is to provide an easy set of tools for a software designer to create monitoring or control applications. There are some performance enhancements in the implementation, including data caching, parallel access to bus masters, and aggregation of device communication. Still the fundamental goal has been ease of use, flexibility and correctness rather than speed. ### DS2740 The **DS2740 (3)** is a class of battery charging controllers. This chip measures voltage and volthours, and has a pin that can be used for control. ## ADDRESSING All 1-wire devices are factory assigned a unique 64-bit address. This address is of the form: - **Family Code** 8 bits - **Address** 48 bits - **CRC** 8 bits - Addressing under OWFS is in hexadecimal, of form: - **01.123456789ABC** where **01** is an example 8-bit family code, and **12345678ABC** is an example 48 bit address. The dot is optional, and the CRC code can included. If included, it must be correct. ## DATASHEET http://pdfserv.maxim-ic.com/en/ds/DS2740.pdf ## SEE ALSO ### Programs **owfs (1) owhttpd (1) owftpd (1) owserver (1)** **owdir (1) owread (1) owwrite (1) owpresent (1)** **owtap (1)** ### Configuration and testing **owfs (5) owtap (1) owmon (1)** ### Language bindings **owtcl (3) owperl (3) owcapi (3)** ### Clocks **DS1427 (3) DS1904 (3) DS1994 (3) DS2404 (3) DS2404S (3) DS2415 (3) DS2417 (3)** ### ID **DS2401 (3) DS2411 (3) DS1990A (3)** ### Memory **DS1982 (3) DS1985 (3) DS1986 (3) DS1991 (3) DS1992 (3) DS1993 (3) DS1995 (3) DS1996 (3) DS2430A (3) DS2431 (3) DS2433 (3) DS2502 (3) DS2506 (3) DS28E04 (3) DS28EC20 (3)** ### Switches **DS2405 (3) DS2406 (3) DS2408 (3) DS2409 (3) DS2413 (3) DS28EA00 (3) InfernoEmbedded (3)** ### Temperature **DS1822 (3) DS1825 (3) DS1820 (3) DS18B20 (3) DS18S20 (3) DS1920 (3) DS1921 (3) DS1821 (3) DS28EA00 (3) DS28E04 (3) EDS0064 (3) EDS0065 (3) EDS0066 (3) EDS0067 (3) EDS0068 (3) EDS0071 (3) EDS0072 (3) MAX31826 (3)** ### Humidity **DS1922 (3) DS2438 (3) EDS0065 (3) EDS0068 (3)** ### Voltage **DS2450 (3)** ### Resistance **DS2890 (3)** ### Multifunction (current, voltage, temperature) **DS2436 (3) DS2437 (3) DS2438 (3) DS2751 (3) DS2755 (3) DS2756 (3) DS2760 (3) DS2770 (3) DS2780 (3) DS2781 (3) DS2788 (3) DS2784 (3)** ### Counter **DS2423 (3)** ### LCD Screen **LCD (3) DS2408 (3)** ### Crypto **DS1977 (3)** ### Pressure **DS2406 (3) TAI8570 (3) EDS0066 (3) EDS0068 (3)** ### Moisture **EEEF (3) DS2438 (3)** ## AVAILABILITY http://www.owfs.org ## AUTHOR Paul Alfille (paul.alfille@gmail.com)