--- name: "DS1977" section: "3" platform: "linux" package: "owfs-doc" version: "3.2p4+dfsg1-6" release: "Debian 13 (Trixie)" platforms: ["linux"] url: "https://new.carta.tech/DS1977" --- # DS1977(3) Password Protected 32kbit Memory iButton ## NAME **DS1977** - Password Protected 32kbit Memory iButton ## SYNOPSIS Non-volatile memory. **37** \[.\]XXXXXXXXXXXX\[XX\]\[/\[ **memory** \| **pages/page.\[0-510\|ALL\]** \| **set\_number/full** \| **set\_number/read** \| **set\_password/enabled** \| **set\_password/full** \| **set\_password/read** \| **use\_number/full** \| **use\_number/read** \| **use\_password/full** \| **use\_password/read** \| **address** \| **crc8** \| **id** \| **locator** \| **r\_address** \| **r\_id** \| **r\_locator** \| **type** \]\] ## FAMILY CODE *37* DS1977 ## SPECIAL PROPERTIES ### memory *read-write, binary*\ 32704 bytes of memory. Possibly protected by a password. ### pages/page.0 ... pages/page.510 pages/page.ALL *read-write, binary*\ Memory is split into 511 pages of 64 bytes each. *ALL* is an aggregate of the pages. Each page is accessed sequentially. ### set\_number/full set\_number/read *write-only, ascii*\ Passwords entered as numbers, either decimal, or hex of form 0x0123456789ABCDEF. Handled the same as *set\_password/xxx* ### set\_password/enable *read-write, yes-no*\ Turn on/off password protection for the DS1977, or return the current state. ### set\_password/full set\_password/read *write-only, binary*\ Passwords (8 byte values) that allow read or full access to the DS1977 memory. The password set by *set\_password/xxx* are stored in the DS1977 and locally in the program as well (as if *use\_password/xxx* was also called). ### use\_password/full use\_password/read *write-only, binary*\ Passwords (8 byte values) that allow read or full access to the DS1977 memory. The password set by ### use\_number/full use\_number/read *write-only, ascii*\ Passwords entered as numbers, either decimal, or hex of form 0x0123456789ABCDEF. Handled the same as *use\_password/xxx* ### use\_password/full use\_password/read *write-only, binary*\ Passwords (8 byte values) that allow read or full access to the DS1977 memory. The password set by *use\_password/xxx* are stored in the program and must match the passwords stored in the DS1977. Changing the DS1977 passwords using *set\_password/xxx* will change these values as well. *use\_password/xxx* are stored in the program and must match the passwords stored in the DS1977. Changing the DS1977 passwords using *set\_password/xxx* will change these values as well. ## STANDARD PROPERTIES ### address ### r\_address *read-only, ascii*\ The entire 64-bit unique ID. Given as upper case hexadecimal digits (0-9A-F).\ *address* starts with the *family* code\ *r address* is the *address* in reverse order, which is often used in other applications and labeling. ### crc8 *read-only, ascii*\ The 8-bit error correction portion. Uses cyclic redundancy check. Computed from the preceding 56 bits of the unique ID number. Given as upper case hexadecimal digits (0-9A-F). ### family *read-only, ascii*\ The 8-bit family code. Unique to each *type* of device. Given as upper case hexadecimal digits (0-9A-F). ### id ### r\_id *read-only, ascii*\ The 48-bit middle portion of the unique ID number. Does not include the family code or CRC. Given as upper case hexadecimal digits (0-9A-F).\ *r id* is the *id* in reverse order, which is often used in other applications and labeling. ### locator ### r\_locator *read-only, ascii*\ Uses an extension of the 1-wire design from iButtonLink company that associated 1-wire physical connections with a unique 1-wire code. If the connection is behind a **Link Locator** the *locator will show a unique 8-byte number (16 character hexadecimal) starting with family code FE.*\ If no **Link Locator** is between the device and the master, the *locator* field will be all FF.\ *r locator* is the *locator* in reverse order. ### present (DEPRECATED) *read-only, yes-no*\ Is the device currently *present* on the 1-wire bus? ### type *read-only, ascii*\ Part name assigned by Dallas Semi. E.g. *DS2401* Alternative packaging (iButton vs chip) will not be distiguished. ## ALARMS None. ## DESCRIPTION ### 1-Wire *1-wire* is a wiring protocol and series of devices designed and manufactured by Dallas Semiconductor, Inc. The bus is a low-power low-speed low-connector scheme where the data line can also provide power. Each device is uniquely and unalterably numbered during manufacture. There are a wide variety of devices, including memory, sensors (humidity, temperature, voltage, contact, current), switches, timers and data loggers. More complex devices (like thermocouple sensors) can be built with these basic devices. There are also 1-wire devices that have encryption included. The 1-wire scheme uses a single *bus master* and multiple *slaves* on the same wire. The bus master initiates all communication. The slaves can be individually discovered and addressed using their unique ID. Bus masters come in a variety of configurations including serial, parallel, i2c, network or USB adapters. ### OWFS design *OWFS* is a suite of programs that designed to make the 1-wire bus and its devices easily accessible. The underlying principle is to create a virtual filesystem, with the unique ID being the directory, and the individual properties of the device are represented as simple files that can be read and written. Details of the individual slave or master design are hidden behind a consistent interface. The goal is to provide an easy set of tools for a software designer to create monitoring or control applications. There are some performance enhancements in the implementation, including data caching, parallel access to bus masters, and aggregation of device communication. Still the fundamental goal has been ease of use, flexibility and correctness rather than speed. ### DS1977 The **DS1977 (3)** is an iButton with static memory that is optionally protected by a password. ## ADDRESSING All 1-wire devices are factory assigned a unique 64-bit address. This address is of the form: - **Family Code** 8 bits - **Address** 48 bits - **CRC** 8 bits - Addressing under OWFS is in hexadecimal, of form: - **01.123456789ABC** where **01** is an example 8-bit family code, and **12345678ABC** is an example 48 bit address. The dot is optional, and the CRC code can included. If included, it must be correct. ## DATASHEET http://pdfserv.maxim-ic.com/en/ds/DS1977.pdf ## SEE ALSO ### Programs **owfs (1) owhttpd (1) owftpd (1) owserver (1)** **owdir (1) owread (1) owwrite (1) owpresent (1)** **owtap (1)** ### Configuration and testing **owfs (5) owtap (1) owmon (1)** ### Language bindings **owtcl (3) owperl (3) owcapi (3)** ### Clocks **DS1427 (3) DS1904 (3) DS1994 (3) DS2404 (3) DS2404S (3) DS2415 (3) DS2417 (3)** ### ID **DS2401 (3) DS2411 (3) DS1990A (3)** ### Memory **DS1982 (3) DS1985 (3) DS1986 (3) DS1991 (3) DS1992 (3) DS1993 (3) DS1995 (3) DS1996 (3) DS2430A (3) DS2431 (3) DS2433 (3) DS2502 (3) DS2506 (3) DS28E04 (3) DS28EC20 (3)** ### Switches **DS2405 (3) DS2406 (3) DS2408 (3) DS2409 (3) DS2413 (3) DS28EA00 (3) InfernoEmbedded (3)** ### Temperature **DS1822 (3) DS1825 (3) DS1820 (3) DS18B20 (3) DS18S20 (3) DS1920 (3) DS1921 (3) DS1821 (3) DS28EA00 (3) DS28E04 (3) EDS0064 (3) EDS0065 (3) EDS0066 (3) EDS0067 (3) EDS0068 (3) EDS0071 (3) EDS0072 (3) MAX31826 (3)** ### Humidity **DS1922 (3) DS2438 (3) EDS0065 (3) EDS0068 (3)** ### Voltage **DS2450 (3)** ### Resistance **DS2890 (3)** ### Multifunction (current, voltage, temperature) **DS2436 (3) DS2437 (3) DS2438 (3) DS2751 (3) DS2755 (3) DS2756 (3) DS2760 (3) DS2770 (3) DS2780 (3) DS2781 (3) DS2788 (3) DS2784 (3)** ### Counter **DS2423 (3)** ### LCD Screen **LCD (3) DS2408 (3)** ### Crypto **DS1977 (3)** ### Pressure **DS2406 (3) TAI8570 (3) EDS0066 (3) EDS0068 (3)** ### Moisture **EEEF (3) DS2438 (3)** ## AVAILABILITY http://www.owfs.org ## AUTHOR Paul Alfille (paul.alfille@gmail.com)